Greetings!
I understand that you have already raised a request through isslovrequests@hpe.com however still awaiting an update.
Please contact HPE support so that the concerned team can be engaged to get this work done.
↧
Re: Request Letter/Certificate of Volatility for HPE ProLiant DL360 Gen10 Server
↧
Re: Port 6: portcfgpersistentenable failed. Configuration is not capable(6).
Greetings!
Please check if Active=Saved Mode (ASM) is enabled.
What happens when you try to enable the port using "portEnable" command"?
Pls refer disabling and enabling ports - persistent states Page# 47 https://docs.broadcom.com/docs-and-downloads/dam/fos-810-ficonguide.pdf
If issue persists, please verify if the HBA in the bay#16 blade is installed in the correct slot. You can compare with the other working blades in the same enclosure.
You may also swap a working blade on bay 6 to further isolate.
↧
↧
Re: Request Letter/Certificate of Volatility for HPE ProLiant DL360 Gen10 Server
Is there an HPE support email address or phone number where I can contact them directly?
I've tried calling and emailing before, but I did not get a response...
↧
Re: Actual IP of blade does not match configured IP
I was able to fix this issue by adding the correct address range under Settings>>Adresses and Identifiers, then changeing the Enclosure group to use the new range, and applying the Group configuration to the Logical Enclosure, after which I was able to delete the old address range.
↧
Re: A very straightforward solution to solving the problem ilo self test error
Note: If you do not fix the problem after several times, unfortunately, the motherboard must be replaced
↧
↧
Self-help Solutions for Frequent issues – Just a Click Away!
HPE Pointnext is focused on improving customer experience through self-solve.
HPE knowledgebase empowers customers with online solutions like never before!
To further enhance the customer experience through self-solve, we would like to share the following most frequently used solutions. These Knowledge documents addresses product issues that are getting logged with HPE.
These Self-help solutions would be refreshed monthly.
Frequently Occurring Issues & Solutions:
- Virtual Connect Setup and Installation Guide
- Certain Network Adapters With The CNA (XE100 series) Unexpected Network Disconnects May Occur
- The system is not booting from the SD and microSD card or USB drive key
- c-Class Enclosure Troubleshooting Guide
- Enclosure, "xxxx", has changed from status OK to Degraded.
- ProLiant Server Blades Compatibility with c7000 and c3000 Enclosures and Firmware
- Does Not Complete POST or Freezes/Stops During POST
- Troubleshooting Hard Disk Failures and Hard Disk Model Number Matrix
- HPE Smart Array Controllers User Guide
- Installing Firmware, Drivers and SPP
- Warranty Lookup
- Contract Linking
- Smart Storage Cache Module and Battery Issues
- Troubleshoot Memory Related Issues
- Correctable or Uncorrectable Memory (DIMM) Errors
- C7000 or C3000 Enclosures - FAN Failed
↧
Re: Stupid Question
I will use haddop along PDSH
↧
Re: Request Letter/Certificate of Volatility for HPE ProLiant DL360 Gen10 Server
Hi
Please use the links below to find the phone number for your region:
Call HPE Product & Solution Support
You can also Chat with HPE Support using this link : Chat with Support
Also adding the link to HPE Pre-Sales team, they may also be able to help you.
↧
https://americanmadepro.com/provexum/
Provexum medication those patients should see a cardiologist without a doubt in my mind because what you're identifying is an underlying vascular anomaly to begin with and whether it's down here or here you're identifying patients with a definitive vascular disease as evidenced by their erectile dysfunction as a consequence of their antihypertensive
Provexum medication so those patients need to see the cardiologist in my mind that's important yeah not at all I think those the the question is are the medications for erectile dysfunction or the what are the downsides of those medications or what are the side-effects of those medications all of those medications.
READ MORE >>>> https://americanmadepro.com/provexum/
↧
↧
AlertMail for a single blade in HP Enclosure
Hi,
How can I disable AlertMail for a single blade in HP Enclosure because few blades in the enclosure not to be alerted.
Thank You
Abdul
↧
HP C7000 Blade connecting to power
Hey Guys
I have a HP C7000 enclosure with 16 X bl460 G6 blades. I bought all the power cable and I bought a 2 bar PDU and I need to know what is the type and model number of your Power Distribution Units.
I know I will need to bring an electrician over to add a breaker I think someone told me 40amp breaker and my c7000 will run N+N.
The input of all 6 power supply is 200-240v 50/60 hz max ac current is 13.7 A
Here in Canada we have 120 V outlets so I know I will to send somebody to add something to the fuse box or I will trip a breaker.
Can you guys tell me what gear you are using to power up your C7000 so I can order it also. I have been looking for about a month and I am going insane!!
Soon I will be running 2 C7000's so if you have 2 running of them please le me know the model number of the PDU's everything lol from the outlet to the C7000 power supply connector. please help
↧
3par with direct attached blade enclosure
Hi
I have 3par 8200 direct attached to c7000 blade enclosure through two virtual connect modules. All 3par controllers are connected to the two virtual connect modules using two fabric ,each fabric correspond to a virtual module ,each fabric have two uplink ports one is active the other is standby ,No external san switch connected.
My question is I have a physical rack mount server work as veeam backup server how can I export the luns of the 3par to this physical servers so I can take backup from the luns over san not over lan.
thanks
I have 3par 8200 direct attached to c7000 blade enclosure through two virtual connect modules. All 3par controllers are connected to the two virtual connect modules using two fabric ,each fabric correspond to a virtual module ,each fabric have two uplink ports one is active the other is standby ,No external san switch connected.
My question is I have a physical rack mount server work as veeam backup server how can I export the luns of the 3par to this physical servers so I can take backup from the luns over san not over lan.
thanks
↧
Re: 3par with direct attached blade enclosure
I have no snapshot license for 3par.
Is it safe to export luns to the veeam backup server ??
Is it safe to export luns to the veeam backup server ??
↧
↧
c7000 with 6120XG blade switch in Bay3/4 not working
I have c7000 blade center with G8 blades. I want my server has one 1G nic (copper) and 2x10G nic (fiber). This is what i have install in blade center.
Bay1: HP 1Gb Ethernet Pass-Thru
Bay2: Empty
Bay3: HP proCurve 6120XG blade switch
Bay4: HP proCurve 6120XG blade switch
My server can see 1G nic but they can't see 10G nic also in blade center i am seeing on 6120XG all 16 ports are not connected. If i remove 1G pass-thru module and put 6120XG switches in Bay1 & 2 then it works...
How do i get 1G working along with 10G fiber switches?
Screenshot: https://imgur.com/a/Isa8Aj9
↧
3par with direct attached blade enclosure
↧
Re: HP C7000 Blade connecting to power
you can refer to the below quickspecs for the available PDUs and UPS
https://h20195.www2.hpe.com/v2/getdocument.aspx?docname=c04128339 ( Page: 14)
use the power advisor to calculate the power requirement at the site.
https://paonline56.itcs.hpe.com/?Page=Index
Based on this you can use the power backup / UPS to power on the entire enclosure and for uninterrupted power.
you can refer to the power supply configuration on C7000 : https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=emr_na-kc0107478en_us
Refer to C7000 Enclosure cabling: https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c03899627
You can also refer to the installation and setup guide for C7000: http://h20628.www2.hp.com/km-ext/kmcsdirect/emr_na-c00698286-13.pdf
For proper redundancy, make sure you connect your power supplies to different power sources / PDU / UPS.
If you need further asssitance, you can opt for a consulting service with HPE.
↧
request for quotation attach file
1- LICENSES, OPEX (Licenses - HPE 5 year post warranty Foundation Care Next Business Day Service (H7J32AC): 1) 3x - C7000 Blade Enclosure with IC Service: P/N - 686611-B21, S/N - CZ3324FXR6; P/N - 686611-B21, S/N - CZ3324FXDP; P/N - 681844-B21, S/N - CZ3341R04F 2) 1x - C7000 Blade Enclosure Service: P/N - 507015-B21, S/N - SGH314RHL6 3) 30x - ProLiant BL4xxc Service: P/N - 641016-B21, S/N - SGH314RKN0; P/N - 641016-B21, S/N - SGH314RKMW; P/N - 641016-B21, S/N - SGH314RR4T; P/N - 641016-B21, S/N - SGH314RR4S; P/N - 641016-B21, S/N - CZ3341R04V; P/N - 641016-B21, S/N - CZ3324FXRH; P/N - 641016-B21, S/N - CZ3324FXRJ; P/N - 641016-B21, S/N - CZ3324FXDW; P/N - 641016-B21, S/N - SGH314RR4P; P/N - 641016-B21, S/N - SGH314RR4R; P/N - 641016-B21, S/N - SGH314RKN5; P/N - 641016-B21, S/N - CZ3341R04X; P/N - 641016-B21, S/N - CZ3341R04M; P/N - 641016-B21, S/N - CZ3324FXRD; P/N - 641016-B21, S/N - CZ3324FXDX; P/N - 641016-B21, S/N - CZ3324FXDY; P/N - 641016-B21, S/N - CZ3324FXDV; P/N - 641016-B21, S/N - CZ3324FXRK; P/N - 666158-B21, S/N - CN731102GQ; P/N - 666158-B21, S/N - CN730805L2; P/N - 666158-B21, S/N - CN731102GT; P/N - 641016-B21, S/N - CZ3341R04P; P/N - 666158-B21, S/N - CZJ3410BV5; P/N - 666158-B21, S/N - CZJ3410BV6; P/N - 641016-B21, S/N - CZ3341R04S; P/N - 641016-B21, S/N - CZ3341R04K; P/N - 641016-B21, S/N - CZJ45103RD; P/N - 641016-B21, S/N - CZJ45103RC; P/N - 641016-B21, S/N - CZ3324FXRL; P/N - 641016-B21, S/N - CZ3324FXRF 4) 4x - ProLiant with DMR ProLiant BL6xxc Service: P/N - 727959-B21, S/N - CZJ45103N0; P/N - 727959-B21, S/N - CZJ45103MY; P/N - 727959-B21, S/N - CZJ45103MZ; P/N - 727959-B21, S/N - CZJ45103MX 5) 13x - B Series 4/24-12 c-Cls Switch Service: P/N - AJ821B, S/N - CN8320B009; P/N - AJ821B, S/N - CN8320B03J; P/N - AJ821B, S/N - CN8316B00E; P/N - AJ821B, S/N - CN8316B00K; P/N - AJ821B, S/N - CN8320B024; P/N - AJ821B, S/N - CN8320B02L; P/N - AJ820B, S/N - CN8305A03F; P/N - AJ820B, S/N - CN8305A031; P/N - AJ821B, S/N - CN8337B0EH; P/N - AJ821B, S/N - CN8337B0DZ; P/N - AJ821B, S/N - CN8451B0AT; P/N - AJ821B, S/N - CN8451B0B2; P/N - AJ821B, S/N - CN8451B0AU 6) 1x - MSA 2040 Storage Service: P/N - C8R14A, S/N - 2S6446B087 7)1x - MSA2000 G3 Array Service: P/N - AW567A, S/N - 2S6049C638 ) QTY-01
2- BLADE SYSTEM,BL460C,GEN10,HPE ( "HPE Server Equipment with listed below specification: 1) HPE ProLiant BL460c Gen10 v6 10/20Gb FlexibleLOM Configure-to-order Blade Server (P09524-B21) – 1 EA; 2) HPE BL460c Gen10 Intel Xeon-Gold 6248 (2.5GHz/20-core/150W) FIO Processor Kit (P06820-L21) – 1 EA; 3) HPE BL460c Gen10 Intel Xeon-Gold 6248 (2.5GHz/20-core/150W) Processor Kit (P06820-B21) – 1 EA; 4) HPE 64GB (1x64GB) Quad Rank x4 DDR4-2933 CAS-21-21-21 Load Reduced Smart Memory Kit (P00926-B21) – 12 EA; 5) HPE 400GB SAS 12G Mixed Use SFF (2.5in) SC 3yr Wty Digitally Signed Firmware SSD (P04525-B21) – 2 EA; 6) HPE 12W Smart Storage Battery (up to 3 Devices) for BladeSystem Server (P01363-B21) – 1 EA; 7) HPE Smart Array P204i-b SR Gen10 (4 Internal Lanes/1GB Cache) 12G SAS QMH2672 16Gb Fibre Channel Host Bus Adapter (710608-B21) – 1 EA;
3- FLEX FABRIC ADAPTER,20Gb,700763-B21,HPE ( HPE FlexFabric 20Gb 2-port 650FLB Adapter (700763-B21)) QTY- 10
4- ULTRIUM CLEANING CARTRIDGE,C7978A,HPE ( HPE Ultrium Universal Cleaning Cartridge (C7978A)) QTY-20
5- CARTRIDGE,LTO-7,15TB,20PCK,C7977AH,HPE ( HPE LTO-7 Ultrium 15TB Eco Case Data Cartridge 20 Pack (C7977AH)) QTY-5
6- TAPE BARCODE,LABEL PACK,LTO-7,Q2014A,HPE ( HPE Q2014A Ultrium LTO-7 RW Tape Barcode Label Pack (Q2014A)) QTY- 1
7- LICENSES, CAPEX ( Perpetual license, HPE Brocade 8/16Gb Embedded FC Switch 12-port Upgrade E-LTU (T5517AAE) QTY-2
PLEASE QOUTE URGENTLY
↧
↧
Unable to access Active OnBoard Administrator (OA1)
I cannot access the OA interface which is active.
In my case it is OA1 which is active.
I have a C7000 enclosure with two redundant OAs (OA1 and OA2).
OA2 is accessible in GUI and SSH but not OA1.
Enclosure IP mode is activated so it is the IP address of OA1 which is always used when I put OA2 in active.
When OA2 becomes active, it is no longer accessible. It is OA1 in standby which becomes accessible.
The network settings are well configured.
The 2 OAs are in the same subnet.
How to reestablish the connection with the active OA?
↧
Re: Unable to access Active OnBoard Administrator (OA1)
Hi,
Did you try reseating the OA modules?
If not, please try it.
Procedure for the reseat of the OA modules.
Remove and reseat the OA module which is in Stand by.
Wait for a couple of minutes for the stand by OA to boot.
After the Stand by OA is healthy , remove and reseat the Active OA and wait for the OA webpage to respond.
cheers
↧
QSFP28 socket compatible with QSFP transceiver
HI,
We are looing at the new Synergy module with HPE Virtual Connect SE 100Gb F32 Module for Synergy. THe module has 6 QSFP28. Our network can only accommodate 10Gb/sec. Is the HPE Synergy 40GbE/4x10GbE/4x8Gb FC QSFP+ Transceiver compatible with the QSFP28 socket?
Appreciate the input.
Kind regards
Andrew
↧
