Clik here to view.
Re: Blade reported an abnormally low power requirement
Oh thanks for replying.In that case is there any problem if I update the Firmware from 2.10 directly to the latest? Or I gotta update it gradually?EDIT.: I just found out some info that I might have...
View ArticleRe: Blade HP C7000 - Server Blade Enclosure Power Request Denied
Hello,I see that, you have two power supply. Please install in bay 1 and 4. Remove FC module from Bay 3 and 4. Now power on the server and check. If that does not resolve the issue we need to look at...
View ArticleRe: Blade reported an abnormally low power requirement
Hello,I would suggest you follow the suggested customer advisory.If the firmware is very old, we never recommend update firmware with the latest.If you feel this was helpful please click the KUDOS!...
View ArticleRe: HP B-series 8/24c SAN Switch BladeSystem c-Class V7.4.2f firmware update...
When I noticed the same problem on another brocade 300 switch after an upgrade to v7.4.2f I tried to solve this problem by going into more details.The file that produces the problems is called...
View ArticleVirtual Connect in C7000
We have a C7000 with one VIRTUAL CONNECT FLEX-10/10D MODULE (639852-001), how to add a second Virtual connect and configure as Active/Standby mode. Does the firmware need to be upgraded.
View ArticleRe: Virtual Connect in C7000
Hi, To add another VC module to an existing VC domain, you need a identical module. (639852-001) installed in 2nd IC bay of the ennclosure. Make sure that the 2nd VC module firmware is same as the...
View ArticleHP 4Gb VC-FC Module In-Band IPv4 Address: 0.0.0.0
I had a power outage and after power was restored, one of our FC module stopped working, I thought I needed to get a replacement so I did and after inserting that replacement It sill did not work. I...
View ArticleClik here to view.
restful api "device inventory"
Hello guys, is it possible to get information "device inventory" that located in iLO from restful api
View ArticleRe: restful api "device inventory"
Hello,AS per shared snapshots, I can see 366 FLR NIC card is showing degadred and NC552SFP is showing Unknown.I would suggest you follow the below steps first.1. Update the system bios and ILO...
View ArticleRe: HP 4Gb VC-FC Module In-Band IPv4 Address: 0.0.0.0
Hi Allen,Good day!From the shared details I suspect like you might have not installed the VC FC module with the same version which is installed in the corresponding VC FC Module.Do you see amy...
View ArticleCan we add IP v4 static route in Onboard Administrator
Can we add IP v4 static route in Onboard Administrator. I can this command for IPv6 but not for IPv4 ADD OA ADDRESS IPV6 [{<bay number>}| ACTIVE | STANDBY] <ipv6 address/prefixlength>
View ArticleRe: Can we add IP v4 static route in Onboard Administrator
Configures the OA to IPv4 static mode or DHCP mode.In STATIC mode, the IP address and netmask are set to the specified <ip address> and<netmask> respectively. These settings take effect...
View ArticleRe: Can we add IP v4 static route in Onboard Administrator
My observation, IPv4 static route couldn't be added in OA
View ArticleRe: EOL/EOS
Where is the EOS list for enterprise equipment including HPE Servers, Storages, Tape Libraries, PARISC, etc? (C'mon HPE, just need an excel sheet of it. None of this: Go to here to the retired portal...
View ArticleRe: Extremely bad (slow) performance from iPDU web interface
I know this is a really old thread but did you ever sort this out?I have a AF525A running firmware 2.0.51.12 (boot version 2.0.0) and I find it painfully slow to use via MS Edge or even Chrome.Is there...
View ArticleRe: Extremely bad (slow) performance from iPDU web interface
I think you should conider creating a new topic instead to get a response
View ArticleHPE ConvergedSystem 300 2.0
HiI need to know the HPE ConvergedSystem 300 2.0 EOSL and RoadmapI can't find this information on the support siteThanks a lotGaetano
View ArticleC7000 upgrade(OA and interconnects)
Currently running a mix of HP BL460 gen 8 and 9 in a C7000 chassis. After purchasing a Gen 10 I noticed that our OA is currently running v4.4 and according go the compatibility matrix the OA needs to...
View ArticleRe: C7000 upgrade(OA and interconnects)
Hello,You can update the OA firmware to the latest. About the interconnect firmware you can udate in hop. Please have the configuration backed up just to be in safer side.Thanks
View ArticleRe: HPE ConvergedSystem 300 2.0
Hi ,Thank you for the Post.Please refer Page Nm 6 https://h20195.www2.hpe.com/V2/GetPDF.aspx/4aa5-9215enw.pdfIt has the information about the Road Map. We shall check if we get the EOSL details and...
View ArticleHow to tell the age of my HP Proliant DL380 G7 and DL360 G8 servers from...
HiI just took over a new job and we have 5 servers that I am trying to figure out the age of as they are critical production servers.Is there a way to tell how old a server is by its serial number? HP...
View ArticleRe: How to tell the age of my HP Proliant DL380 G7 and DL360 G8 servers from...
If you take this partSGH242It means year "2" - this is 2012and week 42so this is October 2012. Consider to remove the serial numbers from your post.
View ArticleRe: How to tell the age of my HP Proliant DL380 G7 and DL360 G8 servers from...
Greetings!The same logic to decode serial# as mentioned in web-link below should apply on proliant servers as well. The link also has warranty check...
View ArticleRe: C7000 upgrade(OA and interconnects)
Hi, Greenpaddy,I have C7000 chassis with mix of BL460c G7, G8 and G9 and did an update of the OA from 4.5 to 4.95 without an issue.Everything after the update was working properly. I would recommend...
View ArticleRe: C7000 upgrade(OA and interconnects)
Thank you both for the advice. How does one backup the config before hand? I dont see an option in the OA?I also read that you have to update the OA from a machine that is on the same network as the OA...
View ArticleRe: C7000 upgrade(OA and interconnects)
Connect with ssh to the Active OA, then you type:UPLOAD CONFIG <url of your ftp/tftp server>Also, if you do not have ftp/sftp/tftp server configured you could do:SHOW ALL then you copy paste the...
View ArticleRe: C7000 upgrade(OA and interconnects)
Plan is to preform over a weekend, onsite at remote location.Backup OA per steps provided.Preform upgrade in hop fashion...4.4 > 4.5 > 4.6 > 4.8 > 4.9.If anything were to go wrong would the...
View ArticleRe: C7000 upgrade(OA and interconnects)
Hey, Greenpaddy,since I can see you have configured a Virtualization on a chassis with many blades, you know that potentially there is always something that could go wrong. But in this case I doubt...
View ArticleRe: C7000 upgrade(OA and interconnects)
Happy to say the upgrade was successful. I preformed it in a hop fashion 4.4> 4.5 >4.6>4.8 with no issues in between. Each stage took about 10-12 mins per. I ran out of time and didnt get to...
View ArticleRe: C7000 upgrade(OA and interconnects)
I am glad all went fine, I am sure you will go to 4.96 without an issue. Thanks for posting, I just realized I am running 4.95 and there is a newer version. I will update soon.I guess my advise was...
View ArticleRe: How to tell the age of my HP Proliant DL380 G7 and DL360 G8 servers from...
Please let us know if your query has been answered
View ArticleRe: HPE ConvergedSystem 300 2.0
Hi ,Kindly let us know if the link was useful.Also regarding the EOSL, currently no links are available. You may check with the re-sellers / the Sales team.Thank you
View ArticleRe: HPE ConvergedSystem 300 2.0
Hi,The link was helpful and the dealer provided the necessary information (EOSL Jan 2022)Thanks a lotGaetano
View ArticleRe: HPE ConvergedSystem 300 2.0
Hi ,Thank you for your prompt response.If you feel this was helpful please click the KUDOS! Thumbs below!Thank youRam
View ArticleProblema boot da usb con hp allinone e bios f.10
Buongiorno ho un hp allinone con bios f.10. Dovendo il pc nuovo andare in assistenza ho necessità di creare un'immagine del disco ove ho installato programmi a pagamento.Pur avendo seguito con successo...
View ArticleRe: Problema boot da usb con hp allinone e bios f.10
Hi,You have reached the wrong company for HP products (Laptops, Desktops, Printers)For HP products, you may have to register and post in the HP Support Forums: https://h30434.www3.hp.com/
View ArticleEOS and Virtual Connect
OK,Can someone please provide a link as to the announcement of EOL/EOS of c-class stuff?VirtualConnect 10GbE has been around for some time but still pretty much the "latest" tech available, yet I've...
View ArticleKVM switch
HPE IP and Server Console Switches G2 的型号的交换机上电后，电源指示灯一直闪烁，无法进入系统。Google Translated:After the switch of HPE IP and Server Console Switches G2 is powered on, the power indicator keeps flashing and...
View ArticleRe: EOS and Virtual Connect
Hello Xavier,Please find the information for the requested products belowProduct SKU Product Name EoDSP date EoSSP date EoSL date455880-B21...
View ArticleRe: EOS and Virtual Connect
Thanks, this is useful.However, I have to ask: where is this information published? Is there a site where there is a table grouping all the products and their end dates?I did see find one, but it...
View Articleimpmitool memory status changed to disabled after iLO update from 2.72 to 2.75
Greetings,Encountered following issue:For example on FW 2.72 impi responce:Memory Status | 0 error | okAfter update to 2.75:Memory Status | disabled | nsBest regards, Ilya
View ArticleSizing question: Replacement of C7000 with 5 active blades (2 Clusters and 1...
Hi everyone,we want replace our current c7000 with another solution. We might stay with HPE on this one.As we bought this blade system we had much more virtual maschines (more into SaaS now) and they...
View ArticleRe: EOS and Virtual Connect
Hello Xavier,Greetings.EoS/EoL information are available only through HPE channels. Through the dedicated accounts team. These information is not available on a public platform. Please contact HPE...
View ArticleRe: impmitool memory status changed to disabled after iLO update from 2.72 to...
Hello Ilya,Thank you for sharing your query.Could you please try updating the iLO Firmware to 2.77 and then check the...
View ArticleRe: Sizing question: Replacement of C7000 with 5 active blades (2 Clusters...
Hello Stephan, For this i would recommend to contact pre-sales team.You may get the contact from the below link:https://www.hpe.com/us/en/contact-hpe.htmlAlso you may refer to elow link for power...
View ArticleC7000-BLADE new VC wrong default password
HiI have installed new VC in my C7000-BladeSystem while I am trying to acces to it using the default credential that comes with, the VC gives me Login incorrect.I tried to reset it and reconnect to...
View ArticleRe: C7000-BLADE new VC wrong default password
HiYou could try a factory reset. The following guide is a little old -https://support.hpe.com/hpesc/public/docDisplay?docId=c03478426 page 115 but it should work
View Article