What is Solutions ID (Onboard Administrator)
Hi all, When you run show enclosure info in the OA. You find a line saying: Solutions ID: 0000000000000000 .There is a command to set this and the help message for this command is:SET SOLUTIONSID "Byte...
View ArticleC3000 Firmware for Onboard Administrator
Hi Can any body give me a Link For Both The enclosure OA Firmware and the firmware for My Bades etc BL460C G1 Cannot seem to find them anywhere Thanks
View ArticleRe: C3000 Firmware for Onboard Administrator
Go to www.hp.com, select drivers+firmware. servers and look for BL460c (without G__ for G1). C3000 OA is using same firmware than C7000. Here is a windows page:...
View Articleexternal usb drive
Hi Bosses! I want to know if it is possible to copy data from a VPAR on bl890c i4 unto an external drive via the usb port. Thank you kingsley
View ArticleNew virtualisation setup - advice needed
I'm currently looking at new hardware for our in-house virtualisation setup. The new setup will be spanned across two datacentres and I'm set on using Veeam for backup and replication (already use the...
View ArticleRe: external usb drive
Supported USB devices are DVD, mouse and keyboard only, but it should work ... consider to create vxfs file system on that disk. But maybe the better solution is to use a network share?
View ArticleHow to reset Blade power on RED LED without replace system board
Hi , all I have some Blades G1, G6 , and most have power on with red led blinking, Is anyway could rest it, without replace system board , Thks
View ArticleRe: How to reset Blade power on RED LED without replace system board
It means there is an issue. Connect to ILO and inspect the status of the hardware, check the IML logs. Once the issue is fixed, the red LED will turn off.
View ArticleRe: How to reset Blade power on RED LED without replace system board
the system unable to power on, just red led blinking, check the log: Could not determine the IP address of the management processor for the requested blade tried swap out Proc, reset SW 6, no luck,...
View ArticleProblem with NC512m and ESXI 5.1u2 Custom Hp Image
Hi I have a HP C700 with 4 blades BL685c gen 1 and one blade BL465c gen7, all the blades have HP mezzanine NC512m cards installed in the ILO Management Software I can see that each blade has one port...
View ArticleBL460c Gen 1 and Gen 9 Compatibility
Hello We recently received some new HP BL460c Gen 9 blades for our c7000. Upon unboxing I noticed the firmware warning that the Onboard Administrator should be at version 4.30. However we also have...
View ArticleRe: BL460c Gen 1 and Gen 9 Compatibility
Support answered my question, Gen1 and Gen9 are not compatible in same chassis.
View ArticleRe: BL460c Gen 1 and Gen 9 Compatibility
bailey80 wrote:Support answered my question, Gen1 and Gen9 are not compatible in same chassis.I'm not sure if that is correct. I checked with a couple of people in product enginerring and no one knows...
View ArticleRe: 3G SAS blade firmware failure
5 Years down the line and I have the same error, how did you solve it? Assuming that you did...
View ArticleRe: 3G SAS blade firmware failure
Fixed it now. Had too update the Onboard Administrator to work with the lastest version of the frimware on the SAS Blade.
View ArticleLatest iLO2 version for G5 blades
I'm trying to find out if 2.29 is a supported version for the bunch of BL260c G5 servers that we have. Right now they are running 2.27, although the latest version available when searching drivers and...
View ArticleRe: Latest iLO2 version for G5 blades
Even G1 blades are using ILO2, but hardware after EOL is no longer tested, hence the last tested version is listed.But it is the same ILO, so it works with newer versions too.
View ArticleHPSUM 7.5.0 Credential issue: impossible to connect to OA
Hi, Had to upgrade firmware on a C7000 Blade system with Integrity servers BL860CI2 & BL870CI2. Launched bundle HPSUM 7.5.0 but impossible to connect to OA. Always msg: Credentials problems. Tried...
View ArticleRe: HPSUM 7.5.0 Credential issue: impossible to connect to OA
I prefer to update these servers without SUM. This helps: http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=mmr_kc-0119690 Cosider to put the files on an USB stick and connect it to the active...
View ArticleNICs that support FLReset
Hi All We need to add some Nics to our BL460c G6 blades that support FLReset (Function Level Reset) for XEN/KVM Virtualisation. We have about 30 of these G6 blades and all have the onboard Broadcom...
View Article