Re: BL460c Gen10 - Memory Configuration Reccomendation
Hello, Optimal memory performance is achieved when the system is configured with a fully homogeneous and balanced memory configuration.Each processor socket contains six memory channels that support...
View ArticleRe: Powershell cmdlet to install a CA certificate on c7000 Onboard Administrator
Use the following cmdlet to import SSL certificate to OAStart-HPOACertificateDownload -Connection $connection -Type OA -URL ftp://10.12.23.17/cer_southking/ldap_southking.cer -Bay <<Bay number of...
View ArticleGet Connected to HPE – let us worry about your technology so you can focus on...
Unlock all the benefits of your technology investment by connecting your products to HPE. With 24x7 monitoring and pre-failure alerts, you'll solve problems faster and minimize downtime. And should a...
View ArticleRe: Powershell cmdlet to install a CA certificate on c7000 Onboard Administrator
It's working now - thanks for the valuable advice!
View Articleperformance c7000 internal
Dear all,we have a c7000 enclosure with bl 460c gen9 blades which are esxi hostsnow the issiue is that copy data from vm to vm what should stay in the same enclosure has only 80 Mb performancecopy...
View ArticleBlades not powering up
First I want to say I am not a company. I am just a guy playing around with some old equipment.I have an old C7000 with a couple of 460 G7's. I initially set everything up with two 3120X's and...
View ArticleRe: Blades not powering up
wrote:First I want to say I am not a company. I am just a guy playing around with some old equipment.I have an old C7000 with a couple of 460 G7's. I initially set everything up with two 3120X's and...
View ArticleRe: Blades not powering up
wrote:irtual Connect Flex-10 Ethernet Modules do support 10GbE and more options such as splitting a flex-NIC into 4 ports of varying speed to equal 10Gbmaybe a defective 6120? Mismatched firmware...
View ArticleRe: Blades not powering up
I am getting this message in the system log for all of my blades but the only thing I can find concerns OA firmware 4.6 that states to upgrade to 4.7 but I am on 4.7OA: Device in bay #2 power delayed...
View ArticleRe: Blades not powering up
Virtual connect mode was still on. Solution was to go underEnclosure Settings -> Reset Factory Defaults -> Clear VC ModeOnce vc mode was disabled the blades powered up.
View Articlec7000 - mix of different OA Hardware Revisions possible?
Hello,currently we got a 456204-B21 Open Administrator (HW Revision "B2") in our productive c7000. Next to Virtual Connect.We also got a spare 407296-001 Open Administrator in one of our retired...
View ArticleRe: c7000 - mix of different OA Hardware Revisions possible?
Hi ,As per your query I found below information which can be helpful."The part number for HP Onboard Administrator is displayed as part number 407296-001 on the HP BladeSystem c7000 Enclosure Onboard...
View ArticleC7000 test setup
Hi alli have a c7000 im using as a test bed. i need to test the VC-FC 4Gb module and wondered what the simpliest but most effective way to test one would be.would it be possible to connect a VC-FC...
View ArticleRe: c3000 Sharing storage across blades
Hello,As the Local Storage of each blades are tied to its own servers, you cannot share the Drive space to pool together, unless its a Blade Storage server.If Blade Storage server is not a possible...
View ArticleRe: Error: Power loss due to overheating. Attempting to restore power Server:...
Hello,To prevent possible server Blade overheating, always populate each processor socket with a processor socket cover and a heatsink blank or a processor and a heatsink.Ensure Proper Blanks are...
View ArticleRe: C7000 test setup
Hello,I hope the VC-ENET / FlexFabric Modules are installed on the Primary two interconnect slots of the enclosure.We strongly suggest using the 4GB VC-FC with conjuction to a VC ENET/Fabric Modules on...
View ArticleRe: C7000 test setup
HiThanks for you replyyes im using the Vc-enet aswell.the one thing i wanted to confirm is can i configure it so the 2x blades with dual FC ports be mapped to 2x ports on the VC-Fc card? Thanks
View ArticleNetwork problem
Hi alli have some problem with networking.We have two hp blade systems c3000 and i want to move two bays to uper one, when i do this, machine is working fine but id doesn't have network, im also...
View Article