Re: Migrate back to VCM from OneView
As a followup from yesterday, I finally was able to flash the VC module and was eventually able to login to the web gui. Hopefully this will help someone migrating off OneView.What was required, was an...
View ArticleRe: C-7000 ilo3 login problem
So my question was going to be "if you don't turn on 5 and 6 with 1, can you continue on past where it says "maintenance switch detected in on position, please turn off and reboot."See, in a rash...
View ArticleRe: C-7000 ilo3 login problem
So I've reboot ed with only maintenance switch1 on. Unexpected. The SUV cable and display did not come on as it had with all ten s witches on. Still one health led flashing. With allten on all front...
View ArticleRe: C-7000 ilo3 login problem
I should clarify: when attempting to login to the container ipv4 address, with or without name and password, and MS 1 on, I get back something something "(404) not found". The ethernet cable is plugged...
View ArticleRe: IML log how to mark repaired?
Hi,i´m on the same subject, i tried the IML Log Repair Command in PS & iLORest CMD : iLOrest > serverlogs --selectlog=IML -r 36...and it failes with : "iLO response with code [400]: An unknown...
View ArticleRe: C-7000 ilo3 login problem
I don't think so. I log into ilo using the blade ipv4 address. The container ipv4 address gets a 404 not found error. Once logged into ilo with the blade address, there is a black screen with a...
View ArticleRe: C-7000 ilo3 login problem
System maintenance switches 1,3, and 5 turn on the blade and suv cable, and get you into all the start up and configuration screens. Dont know why but there it is....Thanks
View ArticleClik here to view.
Re: C-7000 ilo3 login problem
Still not sure about the situation.Do you get the OA logon screen and are you able to logon?It looks like this: You will find the OA IP address at the information screen on the front panel.
View ArticleVC direct attach
Hello there.I've got an old c7000 blade chassis with VC (4.50 or so) flexfabric 10/24 modules for a lab purposes.Well, I've already dealt with c7000 enclosures in the past, but they were equipped with...
View ArticleRe: VC direct attach
Hello, You should consult the Storage Vendor first (VNX) .Since you are plannnig for a multi-vendor environment you need to raise a case with storage vendor to confirm that they also supports this...
View ArticleRe: C7000 - VC - OA - ILO - Compatiblity
I've read in multiple places that iLO --> OA --> VC is the best order. Not sure why. we've been doing OA --> VC and dealing with iLO separately (sometimes before and sometimes after) and...
View ArticleRe: C7000 - VC - OA - ILO - Compatiblity
From a best practices guide: - update blades online (drivers, firmware, ILO) and OA- update blades offline, if needed- update VC Carefully read the VC firmware release notes !!!Some modules may not...
View ArticleRe: VC direct attach
This is not that answer I was hoping to get here.This particular enclosure is OESed now, it is not supported by the vendor, as along as my VNX storage (the guarantee is over), that's why I got this...
View ArticleRe: C-7000 ilo3 login problem
I have yet to see the onboard administrator. The screen I get with the regular display/suv cable working says "HP Proliant" while checking a bunch of stuff before letting you choose between F9=Setup,...
View ArticleClik here to view.
Re: C-7000 ilo3 login problem
I'm still not really sure what you are doing.First you should get the enclosure's onboard administrator IP address from the front panel in Enclosure Settings screen: Then you should locate the active...
View ArticleRe: C-7000 ilo3 login problem
Right right right!Front screen just as you showThere were options: ipv4/ipv6, static/dynamic I wound up static/ipv4 because I have no internet service. Laptop with ilo console goes wifi to router, then...
View ArticleAdding second AO
In my c700 we have one AO. I want to add the second one...whats the procedure?
View Article