It is just telling you it can't connect to the NIC on the server in that slot. Just ignore it. If that server will remain shut down for a while, you can remove it from a profile. That should stop the messages.
↧
Re: C7000
↧
Re: Storage Spaces Direct with
Same message error when I try Enable-NetAdapterQos
I'm using HPE FlexFabric 10Gb 2-port 556FLR-SFP+ Adapter which is RDMA(RoCE) compatible.
Did you get any feedback from Microsoft ?
↧
↧
Re: "Post-Production" Service Pack for ProLiant (SPP) for Gen8 Server Firmware Upgrade.
You can always boot Intelligent Provisioning and update the firmware off the internet that way as well!
↧
Re: "Post-Production" Service Pack for ProLiant (SPP) for Gen8 Server Firmware Upgrade.
i downloaded PP SPP Gen8 and G7 last week ...
↧
Re: "Device identification data error" on C7000 PSU
i have some condition for PowerSupply of C7000
do you fix this problem?
↧
↧
power supply 5 show "Device identification data error" in OA of C7000
OA Website show "degrade" of C7000, point out "Device identification data error" on power supply 5
replug power supply 5 and OA module can not fix this , i power off /on enclosure of C7000 finally.
insight display show nothing error ,"health check" is good, led is green of power supply.
but fault information still showing on OA website....
how can fix this problem? thanks!
↧
OA module reboot too long more than 2 hours
i have one OA module in C7000 enclosure.
oa console and insight display not use when reboot OA module. but i can ping pass ip of oa.
recovery normal time is more than 2 hours....
the oa firmware is v4.23 and v4.5.
do you see that problems? how fix that?
↧
Re: power supply 5 show "Device identification data error" in OA of C7000
Please post result of oa show all
Thanks
JY
Thanks
JY
↧
Re: OA module reboot too long more than 2 hours
Please post result of oa show all
Thanks
JY
Thanks
JY
↧
↧
Re: "Device identification data error" on C7000 PSU
Please post result of oa show all
Thanks
JY
Thanks
JY
↧
Re: N+N and N+1 Redundancy
Hello Rishi2:
N+1 and N+N are by default terms used in a redundancy context.
When you only have 2 PS, you can't speak about N+N as that isn't redundant. With 2 PS there is only N+N possible.
Rgrds,
↧
HPNA SSH login message "Failed to read binary packet data"
We are seeing
"Server sent disconnect message
type 2 (protocol error):
"Failed to read binary packet data!""
when trying to SSH into our HP Network Automation server. Web login works.
↧
Re: MF NA SSH login message "Failed to read binary packet data"
This is the wrong company for MF software questions. You need to register in the MF Software Forum:
https://community.saas.hpe.com/t5/Network-Automation-Practitioners/bd-p/sws-NA_SUP
↧
↧
ILO Auto Login failed while taking IRC
Hello Experts,
While trying to take IRC of a blade the auto login is not working. I have 6 blades in the enclosure
One blade works fine
In this affected blade there is a exclamation mark and it shows (0.0.0.0)
But ILO Network default gateway settings in OA Network settings is correct and checked pinging from the machine where I logged into OA Console
Under Enclosure Bay IP Addressing apart from the working server bay as i mentioned above other blade "Current Address" shows "Unknown"
Things Already done:
After browsing in HP Forum done a reset of Virtual Buttons option in the OA
How can I resolve this in remote rather than going to the server as it is located remotely
↧
Re: HP FlexFabric 20Gb 2-port 650FLB Adapter support NPIV or NOT
Hey Binhvq.
Our problem turned out to be a mismatch in firmware/driver metric from the behind laying IBM SVC's and and our 650FLB Firmware.
So what type of Storage SVC/Switches do you use?
Btw - please read here : https://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=2148123
Regarding the "tried to re-accquired lock vport_lock" issue.
↧
Connecting to blade problem
When i trying to connect a blade using KVM I get this error.
"Could not Connect Error (0x5) Wait a few seconds and try again"
I have incorrect static IP address in iLO settings (0.0.0.0), how can i reset it to DHCP??? I also try change position junpers (clear nvram..) on blade but it didn't help me.
Command "reset server <bay>" also didn't solve the problem.
Command "connect server <bay>" I get error "Invalid MP IP Address: 0.0.0.0".
BladeSystem c7000.
↧
Re: Connecting to blade problem
F8 during powerup to access ilo parameters
JY
JY
↧
↧
Re: Connecting to blade problem
"When i trying to connect a blade using KVM I get this error.
"Could not Connect Error (0x5) Wait a few seconds and try again""
↧
Which commands to use for HPE Blades System C7000 OA to see KPI variables of blades?
Hello,
I am currently using HPE blades system C7000 Onboard Administrator and need to write a script which can pull the information of KPI veriables (i.e. CPU usage, memory usage, storage etc..) of a perticular blade. Can anyone help me which commands I can use on cli to check these details for a perticular blades or all blades ?
Later i will require to write a script which can pull all KPI varaiable information and save it to a csv or txt file.
Thank you in advance.
↧
Re: mezzanine type 1 and type 2
I would like to see an image to see what each type looks like. I have one installed on a BL460c Gen 9 and can't tell if it's Type 1 or Type 2. I could really use some help on this. Thanks.
↧