Quantcast
Channel: All BladeSystem - General posts
Browsing all 1655 articles
Browse latest View live

Re: Mezzanines for BL460c G8

Workstation and server are very similar, in fact you toggle a dip switch. These parts should fit, but you need a second processor to make the second mezzanine work.Take care, there are MXM and MXM...

View Article


HP VC FC cannot connect SSH or any CLI

Hi all, I have an HP C 7000 enclosure with two VC Enet and two VC FC Module.When I tried to connect to the VC Module CLI via OA SSH., I got this error : User not known to the underlying authentication...

View Article


Re: 2 new c7000s - fans blowing at 89% - why?

I think that is important to have ILO Advanced Pack installed..and take a look to:Title: HP ProLiant BladeSystem Gen8 Server Blades - Enclosure Fans Run At 89% AlwaysObject Name:...

View Article

Fibrechannel adapters only show up on 3 hosts - ESXi 6.0

We have 9 blades in our C7000 and only 3 of them see Fibrechannel adapters in vSphere (esxi 6.0).  This is currently just our lab environment.The server profiles for each blade are exactly the same for...

View Article

Re: HP VC FC cannot connect SSH or any CLI

hebn connecting to the VC Enet module, make sure tio use the VC Enet Administrator password from the tag on the VC Enet module.The VC FC module does not have a CLI and will give an "access denied" if...

View Article


Re: Blade reported an abnormally low power requirement

 so how did you go with this issue ?I'm still receiving this false alert once in a month at least.

View Article

Brand new C7000 Plantinum chassis where all fans goes into blinking amber

Hi,A brand new C7000 PLantinum enclosure with all fans and power module installed has a strange problem.When powering on we get 1-2 seconds with green light on fans then all goes into blinking amber....

View Article

Enclouse C7000 with Bl 460c G6

We just bought a 16 used BL 460c G6 servers with an Enclosure c7000. I am not able to access ILO from anyone of this servers by OA. At Blade Firmware information, says:Device Model: HP ProLiant BL460c...

View Article


Re: Very slow boot on ISO mounted virtual Media

I know this is an older thread but I wanted to put in some feedback that might help some others down the road. I got tired of Windows taking forever to install when using the Java applet and I couldn't...

View Article


Re: Enclouse C7000 with Bl 460c G6

What is the firmware version of the OA?If you attach directly to the blade with video/key/mouse you can manually interact with the iLO setup.  Set it to defaults and then reset iLO and try again.I do...

View Article

Re: Brand new C7000 Plantinum chassis where all fans goes into blinking amber

This is the real problem:no power in the OA module or the Insight display in frontIf the OA is not active, the fans do not know what speed to run, so they report flashing amber and run at full speed....

View Article

Re: Enclouse C7000 with Bl 460c G6

Hi Bob! Thanks for your help!My Chassis OA firmware version is 4.21The blades is blinking a red light in front of it, and can´t power on. I try to use the adapter too, without success.    

View Article

Re: Brand new C7000 Plantinum chassis where all fans goes into blinking amber

As Robert says plus If you have a single OA make sure its in the left hand side (viewed from back) and you have a Power supply in the left hand side (viewed from front)

View Article


Blade C7000 which storagework should I buy

I have a blade c7000 and I would like to buy a storage for connect all servers . which model should I buy? I have two HP VC 8GB 24Ports  and I have one EMC DS-300B , it would be great a storage where i...

View Article

Re: Enclouse C7000 with Bl 460c G6

All of the blades in the enclosure are flashing RED?What is your power configuration?  Use the OA to check power meters to be sure it is OK. -Bob

View Article


HPrest 1.5 : ERROR: 'etag'

Hello guys,I'm using HPrest 1.5 on Ubuntu 14.04 LTS. I'm using the program 'hprest' to login to local server:hprest > login Discovering data from iLO.............Done ERROR: 'etag' hprest >As you...

View Article

Re: HPrest 1.5 : ERROR: 'etag'

Btw, I'm on HP BL460c Gen9

View Article


Onboard Administrator continually reboots after firmware upgrade

I have an old C3000 blade enclosure.  I am in the process of upgrading the firmware for the OA.  I am doing them in order.  Now I am stuck as the OA continually reboots since I upgraded.  Has anyone...

View Article

Re: HPrest 1.5 : ERROR: 'etag'

Okay,I finally found out the solution. The iLO 4 firmware was v2.10. I upgraded it to v2.30 and I can now use the 'hprest' and do the login locally without any problem. 

View Article

Re: Onboard Administrator continually reboots after firmware upgrade

Maybe the update broke something.  Do you have another OA you can install in there to see if that helps?-Bob

View Article
Browsing all 1655 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>