Encryption Performance - Smart Array
Hi, I am looking at adding a The sncryption license to a HPE Smart Array P408i-p SR Gen10 Controller so some local drives can be encrypted. Is there anything documented related to performance when...
View ArticleRe: Storage Spaces Direct with
I'm also running into the same issue with the get-netadapterqos and enable-netadapterqos commands, using the same 556FLR-SFP+ adapters. Did either of you find a solution for this, or a workaround?I had...
View ArticleRe: Storage Spaces Direct with
I never found a solution to this and thus the S2D cluster was never stable enough to go into production. I had multipul tickets raised with Microsoft to find a solution. Nodes BSOD randomly, applied...
View ArticlePowershell Error - Can't multithread to Connect-HPOA or Connect-HPBIOS
This is a cross post in hopes of getting more exposure:Hello, PLEASE NOTE: CONNECT-HPEBIOS (released 10/2017) fixes the issue below. CONNECT-HPOA STILL HAS THIS ISSUE.I have a CSV that i'm importing...
View ArticleRe: Powershell Error - Can't multithread to Connect-HPOA or Connect-HPBIOS
This is a duplicate, please reply in the following topic:https://community.hpe.com/t5/Server-Management-Remote-Server/Powershell-Error-Can-t-multithread-to-Connect-HPOA-or-Connect/m-p/6988104#M7934
View Articledifference between getprpw and getprdef
Hi,I want to know what is the difference between getprpw and getprdef.I am using hpux 11.31... in trusted mode.so if i want to set expwarn value whether i should use modprpw or modprdef?Thanks in advance
View Articlepower supply 5 show "Device identification data error" in OA of C7000
OA Website show "degrade" of C7000, point out "Device identification data error" on power supply 5replug power supply 5 and OA module can not fix this , i power off /on enclosure of C7000...
View ArticleC 7000 blade
Hello i have C 7000 blade with 2 flex fabric 10 GB/24 module and 8 server BL 460 gen9 my probleme is connect this with MSA2040 and SWITCH SN3000B i don't show FibreChannel module in VC Manager and...
View ArticleRe: Connecting to blade problem
Using the adapter shipped with the blade enclosure, you can connect a screen and keyboard directly to the server. then use F8 to reset iLO IP
View ArticleRe: ILO Auto Login failed while taking IRC
Try to apply the IPs in EIPA again, or reset the server physically or by using putty to OA "reset server baynumber"this command will reboot the server
View ArticleC7000 G2 Not Showing Blades
Hi all,New to the C7000 and blade servers in general. Ive come across an issue with my C7000 and the management not showing the blades that are installed. It is showing the installed CISCO switch...
View ArticleRe: C7000 G2 Not Showing Blades
HelloWhat are oa version ?What are blade (type , models) involved ?ThanksJY
View ArticleRe: C7000 G2 Not Showing Blades
I would check the EBIPA section if the ILOs are getting an IP address.
View ArticleRe: C7000 G2 Not Showing Blades
The blades that are currently in the server are:14x BL460C G6 - Firmware version 1.812x BL460C G1 - Unknown Firmware versionThe enclosure firmware is 2.60 on both of the management cardsI have since...
View ArticleRe: C7000 G2 Not Showing Blades
First I would update the OA firmware version.2.60 is probably from year 2010.
View ArticleRe: C7000 G2 Not Showing Blades
Alright ill give it a shot next time Im in the office as I am currnetly away. Ill update the thread when I have tried it. Thanks.
View ArticleRe: C7000 G2 Not Showing Blades
>> BL460C G6 - Firmware version 1.81This is probably the version of the ILO2.Latest is 2.29, update them too.
View ArticleRe: C7000 G2 Not Showing Blades
As this will be the first time that I have updated the firmware, can you just put the latest firmware from the blades and the enclosure together or do version versions work with each other? If I get...
View ArticleRe: C7000 G2 Not Showing Blades
Just onboard administrator and ILO firmware for startingJY
View ArticleHP FlexFabric 10Gb 2-Port 534FLB Adapter Status Unknown
Hello, after reboot of HP BL460c G8 server lost FlexFabric adapter. In ILo shown that status unknown, firmware version N/A. Also in OS Windows Server 2012 R2 shon error code 10 unable to start. I tried...
View Article
