Re: After move HP VC flex fabric modules to other bays I can not access VCM
Great job fixing this issue!I had this same issue EXCEPT: When I saw the message that the Active VC was not in this bay, I connected to what I thought was the backup VC, and tried to type my ID and...
View ArticleLPe1605 UEFI/Bios Settings in BL460c G9
Hi all, Been a while since we have bought new hardware and I’m looking to configure the HBA's with the below settings in line with our SAN Manufacturers guidelines however I can’t seem to find...
View ArticleAdding two more ports to an existing Fiber Channel Uplink - Oneview
Hello Goal:We want to expand the Fiber Channel Uplink from two ports to four ports. Current Setup:Oneview 3.1We have FlexFabric-20/40 F8 Interconnect Modules (two of them, Slot 1 and Slot 2)We have...
View ArticleJan 30-31 - Online Expert Days (HPE Servers) is back !
Please join us for the HPE Servers Expert Day on January 30 and 31. More information available here: http://hpe.to/6003DHgE9
View ArticleMezzanine ports max. power
Hi all,what is the max. power delivery to mezzanine cards?I would llike to put some high-end GPUs (min. 100 watt) into the mezzanine ports.Regards
View ArticleHP Bladesystem and Virtual Connect Firmware upgrades
helloI hope you can help and apologies if this query has been answered already.Our bladesystems (C7000 and BL460) & virtual connect all have out of date firmware and I have been tasked with the...
View ArticleRe: How to get the NIC firmware version on HP BL 465c G7/8 running VMware ESXi ?
Easy way is following:- 1Log on to the respective server with username and password.2Once logged in, go to Run and type devmgmt.msc and click on OK.3Once the Device Manager Window is open à click on...
View ArticleRe: HP FlexFabric 10Gb 2-Port 534FLB Adapter Status Unknown
Hi KratonYou need check what is recommended version of the Driver to use with Firmware installed and vice-versa (check in Release Notes Tab this information) and install that in the Revisionn History...
View ArticleCan't add more than four Network connections in Server Profile Template in...
Hi,We are attempting to create a Server Profile Template to have six network connections, three on Network 1 and three on Network 2 but when we go ahead and attempt to save the settings, I get an error...
View Articlerx2660 VOLTAGE FAULT in System Log by BMC
Several VOLTAGE FAULT has been logged in system log. At a few occations there are also VOLTAGE OK messages logged, but the next VOLTAGE FAULT is logged about 22 hrs later.Cannot see any other error...
View ArticleHP Proliant ML10 Gen9 Drivers
I recently purchase a new HP Proliant ML10 Gen9 Server. i need help to install the drivers for it. im going to install the windows server standard 2012 r2 edition. i have also setup raid unable to...
View ArticleRe: C7000 G2 Not Showing Blades
HelloWhat are oa version ?What are blade (type , models) involved ?ThanksJY
View ArticleRe: rx2660 VOLTAGE FAULT in System Log by BMC
If you look at the front of the server, the status lights will tell you what component is bad. Here's the service manual -- see page 26 for...
View ArticleC7000 G2 Not Showing Blades
Hi all,New to the C7000 and blade servers in general. Ive come across an issue with my C7000 and the management not showing the blades that are installed. It is showing the installed CISCO switch...
View ArticleRe: C7000 G2 Not Showing Blades
HelloWhat are oa version ?What are blade (type , models) involved ?ThanksJY
View ArticlePluging the Brocade 8Gb SAN Switch for HP BladeSystem c-7000
Hello,I have c-7000 up and running with 6 blade servers and 3 blade storages. Everything is already in production. All I can find in installation guide is that the Brocade 8Gb SAN Switch is a...
View ArticleRe: Pluging the Brocade 8Gb SAN Switch for HP BladeSystem c-7000
plug in is not a problem, pull out can be a problem, once in use...
View ArticleClik here to view.
VC Flex10 CX4 issue
I have a c3000 enclosure and two VC Flex-10 modules in interconnect bay 3/4.The unit in bay 3 works by connecing the CX4 in x1 up to the core switch however the one in Bay 4 will not accept the CX4 as...
View ArticleHPE Ethernet 10Gb 2-port 560FLB Adapter
Hello,Is it possible to have 8 NIC's on Virtual Connect Server Profile with one HPE Ethernet 10Gb 2-port 560FLB Adapter?Not sure if this is the answer:"Ethernet adapters NOT support with Flex-10 or...
View Article